219 ? 12 3 4 power photomos relays (high capacity type) mm inch max. 32.0 1.260 max. 43.0 1.693 max. 9.0 .354 features 1. high capacity type power photomos relay. can switch a wide range of currents and voltages. can control various types of loads, from very small loads to a maxi- mum 6a ac/dc current for sequencers, motors, and lamps. 2. low on resistance and high sensi- tivity. low on resistance of less than 50 mw on a par with mechanical relays (aqz262). high sensitivity led operate current of 3 ma (at 25 c 77 f ). 3. ac/dc dual use bi-directional control is possible. there is no need to differentiate depending on the load as was necessary with the conven- tional ssr. 4. 4-pin sil type. 4-pin sil type of (l) 43.0 mm (w) 9.0 mm (h) 32.0 mm (l) 1.693 inch (w) .354 inch (h) 1.260 inch. 5. low-level off state leakage current in contrast to the ssr with an off state leakage current of several milliamps, the photomos relay features a very small off state leakage current of only 10ma even at the rated load voltage. 6. controls low-level analog signals the triac, photocoupler, or ssr cannot be used to control signals of less than sever- al hundred mv. the high capacity type power photomos relay feature extremely low closed-circuit offset voltage to enable control of low-level analog signals without distortion. typical applications ? mercury relay replacement ? railroad, traf?c signals ? compact motors, lamps, heaters ? oa equipment ? measurement instruments types ac/dc type * indicate the peak ac and dc values. output rating* part no. packing quantity load voltage load current inner carton outer carton 60 v 6.0 a aqz262 20 pcs 200 pcs 400 v 1.0 a AQZ264 rating 1) absolute maximum ratings (ambient temperature: 25 c 77 f ) item symbol aqz262 AQZ264 remarks input led forward current i f 50 ma led reverse voltage v r 3 v peak forward current i fp 1 a f = 100hz, duty factor = 0.1% power dissipation p in 75 ma output load voltage (peak ac) v l 60 v 400 v continuous load current (peak ac) i l 6.0 a 1.0 a peak load current i peak 10.0 a 3.0 a 100 ms (1shot), v l = dc power dissipation p out 3.0 w total power dissipation p t 3.0 w i/o isolation voltage viso 1,500 v ac temperature limits operating t opr C40 c to +85 c C40 f to 185 f non-condensing at low temperatures storage tstg C40 c to +100 c C40 f to 212 f photomos relays
aqz262, 264 220 2) electrical characteristics (ambient temperature: 25 c 77 f ) note: recommendable led forward current i f = 5 to 10 ma. for type of connection, see pa ge 35. *turn on/off time n for dimensions, see page 29. n for schematic and wiring diagrams, see page 35. n for cautions for use, see page 40. item symbol aqz262 AQZ264 remarks input led operate current typical i fon 1.0 ma i l = 100 ma v l = 10 v maximum 3.0 ma led turn off current minimum i foff 0.4 ma i l = 100 ma v l = 10 v typical 0.9 ma led dropout voltage typical v f 1.16 v (1.25 v at i f = 50 ma) i f = 10 ma maximum 1.5 v output on resistance typical r on 0.036 w 1.0 w i f = 10 ma i l = max. within 1 s on time maximum 0.05 w 1.4 w off state leakage current maximum i leak 10 m a i f = 0 v l = max. transfer characteristics switching speed turn on time* typical t on 5 ms 4 ms i f = 10 ma i l = 100 ma v l = 10 v maximum 10 ms turn off time* typical t off 0.32 ms 0.14 ms i f = 10 ma i l = 100 ma v l = 10 v maximum 3.0 ms i/o capacitance typical c iso 2.0 pf f = 1 mhz v b = 0 maximum 4.0 pf initial i/o isolation resistance minimum r iso 1,000 m w 500 v dc maximum operating frequency maximum 0.5 cps i f = 10 ma duty factor = 50% i l = max., v l = max. ton input output 10% 90% toff reference data 1. load current vs. ambient temperature characteristics allowable ambient temperature: C40 c to +85 c C40 f to +185 f 2. load current vs. ambient temperature char- acteristics in adjacent mounting i l : load current; i l (max.): maximum continuous load current 3. on resistance vs. ambient temperature char- acteristics led current: 10 ma; continuous load current: 6a (dc)(aqz262) 1a (dc)(AQZ264) 7 6 5 4 3 2 1 0 0 ?0 20 40 60 80 85 100 ?0 aqz262 AQZ264 ambient temperature, c load current, a 80 85 120 100 80 60 40 20 0 0 ?0 20 40 60 100 ?0 ambient temperature, c i l /i l (max.) 100, % =adjacent mounting pitch =10mm .394 inch =20mm .787 inch 2 1.5 1 0.5 0 0 ?0 20 40 60 80 85 ?0 aqz262 AQZ264 ambient temperature, c on resistance, w
aqz262, 264 221 4. turn on time vs. ambient temperature char- acteristics led current: 10 ma; load voltage: 10 v (dc); continuous load current: 100 ma (dc) 5. turn off time vs. ambient temperature char- acteristics led current: 10 ma; load voltage: 10 v (dc); continuous load current: 100 ma (dc) 6. led operate vs. ambient temperature char- acteristics load voltage: 10 v (dc); continuous load current: 100 ma (dc) 10 8 6 4 2 0 0 ?0 20 40 60 80 85 ?0 aqz262 AQZ264 ambient temperature, c turn on time, ms 1 0.8 0.6 0.4 0.2 0 0 ?0 20 40 60 80 85 ?0 aqz262 AQZ264 ambient temperature, c turn off time, ms 5 4 3 2 1 0 0 ?0 20 40 60 80 85 ?0 aqz262 AQZ264 ambient temperature, c led operate current, ma 7. led turn off current vs. ambient temperature characteristics load voltage: 10 v (dc); continuous load current: 100 ma (dc) 8. led dropout voltage vs. ambient tempera- ture characteristics sample: all types; led current: 5 to 50 ma 9. voltage vs. current characteristics of output at mos portion ambient temperature: 25 c 77 f 5 4 3 2 1 0 0 ?0 20 40 60 8085 ?0 AQZ264 aqz262 ambient temperature, c led turn off current, ma 1.5 1.4 1.3 1.2 1.1 1.0 0 0 ?0 20 40 60 100 80 85 ?0 50ma 30ma 20ma 10ma 5ma led dropout voltage, v ambient temperature, c ?.0 ?.5 ?.0 ?.5 ?.0 ?.0 ?.0 ?.0 0.5 2.0 1.0 2.0 1.5 aqz262 AQZ264 8.0 6.0 4.0 voltage, v current, a 10. off state leakage current ambient temperature: 25 c 77 f 11. led forward current vs. turn on time char- acteristics load voltage: 10 v (dc); continuous load current: 100 ma (dc); ambient temperature: 25 c 77 f 12. led forward current vs. turn off time char- acteristics load voltage: 10 v (dc); continuous load current: 100 ma (dc); ambient temperature: 25 c 77 f 0 50 100 10 ? 10 ? 10 ? 10 ?2 AQZ264 aqz262 load voltage, v off state leakage current, a 50 40 30 20 10 0 10 20 30 40 50 0 AQZ264 aqz262 led forward current, ma turn on time, ms 0.5 0.6 0.4 0.3 0.2 0.1 0 10 20 30 40 50 0 aqz262 AQZ264 led forward current, ma turn off time, ms 13. maximum operating frequency vs. load volt- age/current characteristics led current: 10 ma; ambient temperature: 25 c 77 f 14. applied voltage vs. output capacitance characteristics frequency: 10 khz; ambient temperature: 25 c 77 f 15.-(1) on resistance distribution sample: aqz262 led current: 10 ma; continuous load current: 6 a (dc): quantity. n=100; ambient temperature: 25 c 77 f 10 9 8 7 6 5 4 3 2 1 0 0 50 100 150 200 250 300 350 400 450 load voltage, v load current, a maximum operating frequency, time/s duty = 50% 5000 4000 3000 2000 1000 0 0 20 40 60 80 100 aqz262 AQZ264 applied voltage, v output capacitance, pf 80 70 60 40 20 10 50 30 0 0 26.5 27.5 28.5 30.5 29.5 on resistance, m w quantity
aqz262, 264 222 15.-(2) on resistance distribution sample: AQZ264 led current: 10 ma; continuous load current: 1 a (dc); quantity, n=100; ambient temperature: 25 c 77 f 16.-(1) turn on time distribution sample: aqz262 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 16.-(2) turn on time distribution sample: AQZ264 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 80 70 60 40 20 10 50 30 0 0 0.9 1 1.1 1.3 1.2 on resistance, w quantity 80 70 60 40 20 10 50 30 0 056 4 37 turn on time, ms quantity 80 70 60 40 20 10 50 30 0 02 3 4 6 5 quantity turn on time, ms 17.-(1) turn off time distribution sample: aqz262 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 17.-(2) turn off time distribution sample: AQZ264 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 18.-(1) led operate current distribution sample: aqz262 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 80 70 60 40 20 10 50 30 0 0 0.32 0.36 0.4 0.48 0.44 turn off time, ms quantity 80 70 60 40 20 10 50 30 0 0 0.1 0.14 0.18 0.26 0.22 turn off time, ms quantity 80 70 60 40 20 10 50 30 0 0 1.1 1.3 0.9 0.7 1.5 quantity led operate current, ma 18.-(2) led operate current distribution sample: AQZ264 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 19.-(1) led turn off current distribution sample: aqz262 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 19.-(2) led turn off current distribution sample: AQZ264 load voltage: 10 v (dc); continuous load current: 100 ma (dc); quantity, n=100; ambient temperature: 25 c 77 f 80 70 60 40 20 10 50 30 0 0 0.7 0.9 1.1 1.5 1.3 quantity led operate current, ma 80 70 60 40 20 80 50 30 0 0 1.1 1.3 0.9 0.7 1.5 quantity led turn off current, ma 80 70 60 40 20 10 50 30 0 0 0.7 0.9 1.1 1.5 1.3 quantity led turn off current, ma 20.-(1) led dropout voltage distribution sample: aqz262 led current: 50 ma; quantity, n=100; ambient temperature: 25 c 77 f 20.-(2) led dropout voltage distribution sample: AQZ264 led current: 50 ma; quantity, n=100; ambient temperature: 25 c 77 f 21.-(1) bias test at high temperature and high humidity (change of turn on time) quantity, n=10; ambient temperature: 85 c 185 f humidity: 85%, vl=max. 0.8 100 80 60 40 20 0 0 1.24 1.26 1.28 1.32 1.3 quantity led dropout voltage, v 100 80 60 40 20 0 0 1.24 1.26 1.28 1.32 1.3 quantity led dropout voltage, v 10 8 6 4 2 0 110 2 10 3 10 AQZ264 test time, h aqz262 turn on time, ms
aqz262, 264 223 21.-(2) bias test at high temperature and high humidity (change of on resistance) quantity, n=10; ambient temperature: 85 c 185 f humidity: 85%, vl=max. 0.8 22.-(1) low temperature storage test (change of turn on time) quantity, n=10; ambient temperature: C40 c C40 f 22.-(2) low temperature storage test (change of on resistance) quantity, n=10; ambient temperature: C40 c C40 f 2 1.6 1.2 0.8 0.4 0 1 10 10 2 10 3 test time, h aqz262 AQZ264 on resistance, w 10 8 6 4 2 0 1 10 10 2 10 3 AQZ264 aqz262 test time, h turn on time, ms 2 1.6 1.2 0.8 0.4 0 1 10 10 2 10 3 test time, h on resistance, w AQZ264 aqz262 23.-(1) high temperature storage test (change of turn on time) quantity, n=10; ambient temperature: 100 c 212 f 23.-(2) high temperature storage test (change of on resistance) quantity, n=10; ambient temperature: 100 c 212 f 10 8 6 4 2 0 1 10 AQZ264 aqz262 10 2 10 3 test time, h turn on time, ms 2 1.6 1.2 0.8 0.4 0 1 10 AQZ264 aqz262 10 2 10 3 test time, h on resistance, w 5/7/2001 all rights reserved, ? copyright matsushita electric works, ltd. go to online catalog
|
